Protects the front sight from damage caused by normal field use. Open front design allows plenty of light to reach the front blade and provide an enhanced sight picture. Spring steel construction for durability. Available for Model 94 carbine with sight ramp.
SPECS: Steel, blue, matte finish. 1” (2.5cm) long x ½" (12.7mm) wide. Model 94 - ½" high (12.7mm).
More...
Customer ratings for GALAZAN WINCHESTER 94 RAMP SIGHT HOOD BLACK
Number of ratings: 5
From brownells.com: 5
Average rating: 2.4
Disappointing(07/09/2010)
This hood does indeed fit pre '64 model 94 Winchester carbine ramp grooves,and Brownell's does provide the Galazan specs.online. Original hoods are longer ,but the problem is the Galazan .5 inch ht. vs. the original hoods ht. of approx. .565 inch . If the ramp has a front dovetail sight taller than say .270 the bead has less than desirable clearance from the Galazan hoods "ceiling". This too short product fails to allow a good sight picture w/many factory installed Winchester front sights. Now the shooter may have to re zero after installing a shorter front $ight.
Not bad(21/11/2011)
These appear to be hot rolled steel and therefore are a little scaly and not very smooth. I put them on a belt sander and ground the blunt end to a angle so both ends look the same then sanded with 400 grit sandpaper,warmed,and dipped in oxpho-blue then burnished with fine steelwool. They look good enough to be original.
Sight Hood(17/09/2012)
This sight hood has good fit and finish. It allows me to shoot my carbines with out optics as it aids in providing a good sight picture. Additionally, it provides protection for my front sights and adds a novel flare to the look of my guns without a big expense at a gunsmith shop!
It's okay(19/04/2016)
It fits. I'm not sure what part the other reviewers got, but this is far from being asthetically pleasing, or a "good finish". The part was never polished before blueing, it is a dull grey at best, which will never match any model 94 I've ever seen. So in addition to buying the part, dipping it in some bluing is required as well.
Just Don't(03/10/2018)
This hood looks like it came out of the bottom of a used parts box. You can plan on spending time making it look decent. It is also a very tight fit on the ramp: hammer time.
This is the first time I've given a Brownells' product a bad review. Find a used hood instead.
Product no.: 344000007 GALAZAN WINCHESTER 94 RAMP SIGHT HOOD BLACK Mfr Part: PH131 Protects the front sight from damage caused by normal field use. Open front design allows plenty of light to reach the front blade and provide an enhanced sight picture. Spring steel construction for durability. Available for Model 94 carbine with sight ramp.
31.9GBP113£31.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Protects the front sight from damage caused by normal field use. Open front design allows plenty of light to reach the front blade and provide an enhanced sight picture. Spring steel construction for durability. Available for Model 94 carbine with sight ramp.
SPECS: Steel, blue, matte finish. 1” (2.5cm) long x ½" (12.7mm) wide. Model 94 - ½" high (12.7mm).
More...
Customer ratings for GALAZAN WINCHESTER 94 RAMP SIGHT HOOD BLACK
Number of ratings: 5
From brownells.com: 5
Average rating: 2.4
Disappointing(07/09/2010)
This hood does indeed fit pre '64 model 94 Winchester carbine ramp grooves,and Brownell's does provide the Galazan specs.online. Original hoods are longer ,but the problem is the Galazan .5 inch ht. vs. the original hoods ht. of approx. .565 inch . If the ramp has a front dovetail sight taller than say .270 the bead has less than desirable clearance from the Galazan hoods "ceiling". This too short product fails to allow a good sight picture w/many factory installed Winchester front sights. Now the shooter may have to re zero after installing a shorter front $ight.
Not bad(21/11/2011)
These appear to be hot rolled steel and therefore are a little scaly and not very smooth. I put them on a belt sander and ground the blunt end to a angle so both ends look the same then sanded with 400 grit sandpaper,warmed,and dipped in oxpho-blue then burnished with fine steelwool. They look good enough to be original.
Sight Hood(17/09/2012)
This sight hood has good fit and finish. It allows me to shoot my carbines with out optics as it aids in providing a good sight picture. Additionally, it provides protection for my front sights and adds a novel flare to the look of my guns without a big expense at a gunsmith shop!
It's okay(19/04/2016)
It fits. I'm not sure what part the other reviewers got, but this is far from being asthetically pleasing, or a "good finish". The part was never polished before blueing, it is a dull grey at best, which will never match any model 94 I've ever seen. So in addition to buying the part, dipping it in some bluing is required as well.
Just Don't(03/10/2018)
This hood looks like it came out of the bottom of a used parts box. You can plan on spending time making it look decent. It is also a very tight fit on the ramp: hammer time.
This is the first time I've given a Brownells' product a bad review. Find a used hood instead.