CYLINDER & SLIDE
C&S BROWNING HI-POWER TRIGGER PULL REDUCTION SPRING KIT

000000000253 206025002

Description
Ratings (4)

Reduces Pull Weight For A Light, Crisp Trigger Pull

Competition trigger pull spring kits reduce the pull weight of heavy factory triggers by approximately 2½ lbs. for a much improved trigger pull and better accuracy. #25A fits all pre-’91 Browning Hi-Power pistols, and includes (1) 22 lb. hammer spring, (1) reduced power trigger return spring, and (1) reduced power firing pin spring. #25B fits 1991 and later Hi-Power pistols, and includes (1) 22 lb. hammer spring and (1) reduced power firing pin spring.

SPECS: Spring steel. #25A includes (3) springs. #25B include (2) springs.

More...

Customer ratings for CYLINDER & SLIDE #25-B SPRING KIT

Number of ratings: 4
From brownells.com: 4
Average rating: 3.3

Misleading (31/05/2012)

I installed these springs on a new BHP MK3 which originally measured 9.25 lbs at the trigger. After installation the trigger measured 9.25 lbs. The hammer spring was 4 coils longer than the stock or another manutacturer's replacement springs. This means you either have to cut the coils or pre-load the spring extensively to install it on the strut. So unless your hammer / sear interface angle is positive or neutral with really rough surfaces these parts will do little to help the trigger pull. Modifications to the sear spring pressure will however produce changes in the trigger pull weight.

It work !! (25/01/2010)

I just installed the 3 springs in my 1973 BHP
the job it self require some smithing ability , some roll pin in the trigger group are hard to punch out. The Hammer spring is also tricky to replace. The easiest part is the firing pin spring. My High power lost is rock hard trigger and now has a much more manageable trigger pull.
while I was there I also removed the Mag release safety spring. which also help the trigger pull.
Good luck

excellent (01/10/2011)

great spring set, works really well to improve trigger pull and still reliable.

BUT the hammer spring is a bit of a pain to replace (no fault of this set, just be aware) so allow some time or get some advice.

Decent kit, but there were some problems (08/04/2013)

Decided to replace the springs with lighter ones along with a trigger job on the old Hi-power. Installation was a breeze, and everything was good until I reassembled the gun and it would not function correctly. The hammer was binding. Took it all apart and found the replacement spring for the hammer was about 1/4" longer than the original and was fully compressed and binding before the hammer was fully cocked. Ended up having to cut the spring down to get it to the correct length. After that everything functions fine. The kit I ordered was part no. 206-025-001 for the pre-91 Hi-power, as my Hi-power is a 1973. Maybe I got the spring from a later Hi-power by mistake? Not too sure.

Read 4 more ratings on brownells.com

34.9 38.9 2 GBP

Product no.: 206025002
CYLINDER & SLIDE #25-B SPRING KIT
Mfr Part: CS0025B 000000000253 Competition trigger pull spring kits reduce the pull weight of heavy factory triggers by approximately 2½ lbs. for a much improved trigger pull and better accuracy. #25A fits all pre-’91 Browning Hi-Power pistols, and includes (1) 22 lb. hammer spring, (1) reduced power trigger return spring, and (1) reduced power firing pin spring. #25B fits 1991 and later Hi-Power pistols, and includes (1) 22 lb. hammer spring and (1) reduced power firing pin spring.

34.9 GBP 1 £34.90 *

Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse

Add to shopping list

Ask question

Details

Add to shopping list

Ask question

Top takeaways

The kit reduces trigger pull weight by about 2½ lbs for improved pull and accuracy.
#25A is for pre-’91 Browning Hi-Power pistols and includes three springs.
#25B is for Browning Hi-Power pistols from 1991 onwards and includes two springs.

Attributes

Delivery weight: 0.009kg Shipping width: 83mm Shipping length: 146mm UPC : 000000000253

Item details

Made in USA

Product no.: 206025001
CYLINDER & SLIDE #25-A SPRING KIT
Mfr Part: CS0025A 000000002516 Competition trigger pull spring kits reduce the pull weight of heavy factory triggers by approximately 2½ lbs. for a much improved trigger pull and better accuracy. #25A fits all pre-’91 Browning Hi-Power pistols, and includes (1) 22 lb. hammer spring, (1) reduced power trigger return spring, and (1) reduced power firing pin spring. #25B fits 1991 and later Hi-Power pistols, and includes (1) 22 lb. hammer spring and (1) reduced power firing pin spring.

38.9 GBP 0 £38.90 *