The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
More...
Customer ratings for L.E. WILSON 257 WEATHERBY MAGNUM FIRED CASE HOLDER
Number of ratings: 20
From brownells.com: 20
Average rating: 3.8
Does Not Work With Hornady Dies(08/07/2017)
Recently bought this case holder to use after full-length resizing with Hornady New Dimension Custom Grade K-31-specific 7.5x55 Swiss dies. Case mouths would not exit the holder, making trimming impossible. However, I measured the shoulder on the resized brass and a fresh GP-11 cartridge. The GP 11 measured .448." The "resized" brass measured .472." I think the blame clearly lies with Hornady's dies, not the Wilson trimmer. Nevertheless, I am leaving this review because I want other shoppers to be aware that if they plan to use the Hornady dies, they will need to buy the trimmer holder for FIRED cases, Wilson item CH7555.
Frustrated(28/01/2018)
Bought the original one about a year ago, waiting for a rifle to get finished finally got my rifle she's a dream by the way. Now comes the not so good, I load 308, 223, 6.8, and various pistol calipers after my first shooting with new rifle cleaned and resized brass case goes all the way through, does not stop on shoulder as others, so I'm thinking I got a bad one it happens returned to brownells for a new one, same thing happening all over again, this time, it's not rocket scientist stick the case in the gage until it stops on shoulder set your cutter to desired length and trim not that hard. So I'm surprised that I got so lucky to get two too many out of spec maybe case gages
Maybe I do need to be a rocket scientist(08/02/2018)
So it's Charles again from previous post. Would like to remove the poor rating I gave product earlier. I have been using the wrong holder I needed new and full length resized holder for my brass, just goes to show that us part time rocket scientist aren't so smart after all. Product is great.
Works great!(20/04/2011)
Perfect trim jobs from my Wilson trimmer. Just be sure to tap the case into the holder good so it doesn't spin when you go to trim.
nothing special(27/03/2011)
soft material,dents easily when dropped to the concrete floor.
Drop Proof(31/12/2011)
Works great when you don't drop it on a concrete floor.
Works for both New & Fired Lapua Brass(01/03/2011)
If you're using Laupa 6mm BR Norma brass, you won't need to buy the Wilson Trimmer Holder for New Brass. It fits perfect in this one! Just the neck of new Lapua brass protrudes from the Wilson Trimmer Holder for New Brass. I bought both and only use this one.
GREAT Trimmer(01/05/2017)
FINALLY, a case holder that is accurate, easy to use. and very well made. This case holder, combined with the Stainless Ultimate Trimmer, is a perfect match. For those calibers for which Wilson makes a case holder, this combo will be my trimmer of choice.
Buy CH-308W, not this one(30/08/2012)
This holder will NOT work with fully re-sized brass.
Works with my full length and resized(01/11/2012)
Works as advertised. If it does not call L.E. they will get you straighted out. It is probably due to a tight chamber or oversized. Case Holders are set up to work with 98% of the chambers that are out there, but if it does not they will get you the correct holder for you.
Limited use with fully sized 308 cases(20/03/2018)
Let me say, first, that Wilson products and services are top notch, as is Brownells service. (Wilson trimmers are the most accurate I've ever used. I've trimmed hundreds of rifle cases in various calibers.) This particular case holder works for 243 fully sized (new) and fired brass. It does not work with once fired Lake City or Federal fully sized 308 brass. I used two different Redding presses and standard FL sizing Redding and RCBS dies to check this holder. The sized cases would not extend far enough to be trimmed. I do not have small base dies which reduce the case size to a greater degree to allow more efficient chambering in semi-automatic rifles. I did not use factory new, unfired brass. Based on what I've experienced, I would recommend BOTH case holders to prospective buyers. Rifle chambers vary from Target to Hunting to Military. This is not the fault of the manufacturer or the vendor.
I use these trimmer holders in my Sinclair Micrometer Case Trimmer and get superb results. I trim my cases .010 to .015" under SAAMI maximum case length and get amazingly uniform results. The variation is + or - .0005". The jamb fit of the case holds the case in precise alignment. The only downside is the holder grabs the case so snug I have to to tap each trimmed case on a pad to remove it from the holder. Not a big minus when the results I get are so consistent.
Can be upgraded for Lapua Brass(18/02/2011)
You may be able to alter this Holder slightly to avoid having to also buy a New 204 Brass Holder. New Lapua Brass sits too deep inside this Holder, so that the Case Length Trimmer's threaded Adjustment Stop can't reach the case head. But by using a drill press, you can widen the back end of this Holder's hole so that the Adjustment Stop could enter the hole and reach the New Brass case heads. I didn't need to drill very deep, just about 0.1". I used a bit that was a little wider than the Adjustment Stop's face. I don't know if this will work for Norma brass, as I only use Lapua brass.
Not necessary for new Lapua 6mm BR Brass(18/02/2011)
While waiting for my new 6mm BR to arrive I started tooling up and bought both of the Wilson Trimmer Holders for new and fired brass. I'm using only Lapua Brass and I quickly found out that the new brass fits better in the standard Wilson Trimmer Holder.
Need To Revise My Original Rating(31/07/2011)
Unlike new Lapua brass, new Norma brass fits very well in this case holder because of its smaller diameter.
You may not need one of these.(18/02/2011)
You may not need to buy this New Brass Holder, if you buy the standard Holder (for fired brass) and alter it slightly. New Lapua Brass sits too deep inside the standard Holder, so that the Case Length Trimmer's threaded Adjustment Stop can't reach the case head. Using my drill press, I widened the back end of the Holder's hole so that the Adjustment Stop could enter the hole and reach the new brass case heads. I didn't need to drill very deep, just about 0.1". I used a bit that was a little wider than the Adjustment Stop's head. I don't know if this will work for Norma brass, as I only use Lapua brass.
You will need this holder for new brass(01/11/2012)
If you do not want to modify your holder and void your warrenty, you will need this holder.
L.E. will back up everything they make, they added this because your cases sit too deep in the fired holder which does not allow you to trim the case accurately. Bottom Line you need for new brass or full lenght sized brass.
Quality(30/04/2018)
Typical Wilson quality product. Works great to produce exact length cases.
Won't Work for 30-30 with Neck Bumped up(29/03/2014)
If you bump the neck up on your 30-30 cartridges to prevent excessive stretching of the brass there isn't enough of the brass extending outside of the holder to trim
Details: Using a Hornady Headspace gauge, I have found my fired brass to "Headspace" at 1.503"
I set my Redding die up to keep my shoulder at 1.501" to prevent excessive stretching of the brass when resizing
I have been trimming my brass to 2.030", but when I changed where my shoulder was, it seems I can no longer use the Wilson Trimmer Case Holder because the end of my brass is still inside the case holder.
Historically, using the generic Redding die settings my shoulder was at 1.485". This seemed to give me enough brass outside of the case holder to trim.
Wilson fixed my problem(28/04/2014)
I wrote a review on 3/29/14 with complaints about the holder not allowing you to trim if you bump up the neck of the case. I have since been able to contact Wilson and they were nice enough to machine the holder at no cost (outside of shipping it to them). The holder will now work with both cases (standard factory and with the neck bumped up to fit my rifle). I am very happy with the customer service I received and the holder now works great.
Product no.: 749001199 L.E. WILSON 444 MARLIN CASE HOLDER Mfr Part: CH-444M The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749001204 L.E. WILSON 38-40 WINCHESTER CASE HOLDER Mfr Part: CH-3840 The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749001619 L.E. WILSON 223 ACKLEY IMPROVED FIRED CASE HOLDER Mfr Part: CH-223ACK The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749001621 L.E. WILSON 30 M1 CARBINE FIRED CASE HOLDER Mfr Part: CH-CARB The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749001625 L.E. WILSON SAUM FAMILY NEW CASE HOLDER Mfr Part: NCH-RSAUM The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for various case preparation tasks including trimming and deburring.
It provides high accuracy and repeatability due to its precise manufacturing and unique design that mimics a firearm chamber.
The NEW Case Holder variant is compatible with new, unfired brass or cases that have been full length sized for cartridges like 300 Remington SAUM and 7mm Remington SAUM.
Attributes
Cartridge:
300 Remington SAUM,7mm Remington SAUM,6.5mm Remington SAUM
Case Type:
New
Delivery weight: 0.091kgShipping height: 28mmShipping width: 28mmShipping length: 53mm
Item details
Made in USA
Product no.: 749001630 L.E. WILSON 30-30 WINCHESTER NEW CASE HOLDER Mfr Part: NCH-3030 New Case Holder 30-30 Family
Specs:Cartridge: 300 WSM (Winchester Short Mag), 270 WSM (Winchester Short Mag), 7 mm WSM (Winchester Short Magnum), 325 WSM (Winchester Short Mag)Case Type: New
Cartridge:
270 WSM (Winchester Short Mag),7 mm WSM (Winchester Short Magnum),300 WSM (Winchester Short Mag),325 WSM (Winchester Short Mag)
Case Type:
New
Delivery weight: 0.091kgShipping height: 28mmShipping width: 28mmShipping length: 51mm
Item details
Made in USA
Product no.: 749001652 L.E. WILSON 6.5X47MM LAPUA FIRED CASE HOLDER Mfr Part: CH-X47L Trimmer Case Holder 6.5x47mm Lapua
Cartridge:
6 mm Remington,257 Roberts,7 mm Mauser (7 x 57 mm Mauser),6 mm/244 Remington
Case Type:
Fired
Delivery weight: 0.113kgShipping height: 28mmShipping width: 28mmShipping length: 51mm
Item details
Made in USA
Product no.: 749001655 L.E. WILSON BELTED MAGNUM NEW CASE HOLDER Mfr Part: NCH-264WN The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for precision work on rifle cases, including trimming, primer pocket reaming, neck reaming, and deburring.
It provides ultimate accuracy and uniformity in case preparation, with a design that mimics the chamber of a firearm for consistent support.
NEW Case Holders are specifically for new or full-length sized brass, and are compatible with a variety of magnum cartridges including 458, 300, 338 Winchester Magnums, and others.
Attributes
Cartridge:
300 Winchester Magnum,7 mm Remington Magnum,8 mm Remington Mag,7 mm STW,264 Winchester Magnum,338 Winchester Magnum,358 Norma Mag,458 Winchester Magnum,308 Norma Mag
Case Type:
New
Delivery weight: 0.136kgShipping height: 28mmShipping width: 30mmShipping length: 53mm
Item details
Made in USA
Product no.: 749001656 L.E. WILSON WSM FAMILY FIRED CASE HOLDER Mfr Part: CH-WSM The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Specs:Cartridge: 300 WSM (Winchester Short Mag), 270 WSM (Winchester Short Mag), 7 mm WSM (Winchester Short Magnum), 325 WSM (Winchester Short Mag)Case Type: Fired
The L.E. Wilson Rifle Case Holder is designed for precision in trimming and preparing cases, ensuring accuracy and uniformity.
This case holder supports the case body like a firearm chamber, suitable for Fired Case Holders used with Neck Sized Cases and New Case Holders for new or full length sized cases.
It is compatible with various cartridges including 300 WSM, 270 WSM, 7 mm WSM, and 325 WSM, specifically for Fired Case Types.
Attributes
Cartridge:
7 mm WSM (Winchester Short Magnum),300 WSM (Winchester Short Mag),325 WSM (Winchester Short Mag),270 WSM (Winchester Short Mag)
Case Type:
Fired
Delivery weight: 0.091kgShipping height: 28mmShipping width: 28mmShipping length: 53mm
Item details
Made in USA
Product no.: 749001657 L.E. WILSON 204 RUGER FIRED CASE HOLDER Mfr Part: CH-204R Trimmer Case Holder .204 Ruger
Cartridge:
243 Winchester,308 Winchester,260 Remington
Case Type:
New
Delivery weight: 0.113kgShipping height: 28mmShipping width: 28mmShipping length: 51mm
Item details
Made in USA
Product no.: 749001661 L.E. WILSON 6MM PPC FAMILY FIRED CASE HOLDER Mfr Part: CH-PPC The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749001663 L.E. WILSON 30-06 SPRINGFIELD CASE HOLDER Mfr Part: CH-3006 The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for precision in trimming, primer pocket reaming, neck reaming, and deburring.
It supports the case body during the trimming process, similar to a firearm chamber, ensuring accuracy and uniformity.
Compatible with various case types including Fired, New, Neck Sized, and Full Length Sized for cartridges like 30-06 Springfield, 270 Winchester, and 25-06 Remington.
Attributes
Cartridge:
25-06 Remington,270 Winchester,30-06 Springfield
Case Type:
Fired,New
Delivery weight: 0.136kgShipping height: 28mmShipping width: 28mmShipping length: 51mm
Item details
Made in USA
Product no.: 749001664 L.E. WILSON 6MM BR FAMILY FIRED CASE HOLDER Mfr Part: CH-BR Trimmer Case Holder BR Family (Fired Cases)
Product no.: 749011922 L.E. WILSON 243 ACKLEY IMPROVED FIRED CASE HOLDER Mfr Part: CH-243ACK The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for precision in trimming and preparing cases, ensuring accuracy and uniformity.
This case holder supports the case body during preparation, simulating a firearm's chamber for optimal stability.
The product is specifically made for Neck Sized Fired Cases and is compatible with cartridges such as 280 Ackley Improved, 6mm-244 Ackley Improved, and 243 Ackley Improved.
Product no.: 749011926 L.E. WILSON 6MM DASHER CASE HOLDER Mfr Part: CH-DASH The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for trimming and preparing cases with precision and consistency.
It supports both new and fired cases, including 6mm Dasher and 6mm BRA cartridges, for neck sized or full length sized cases.
The case holder mimics a firearm's chamber, ensuring ultimate accuracy and uniformity in case preparation.
Attributes
Cartridge:
6 mm Dasher,6mm BRA
Case Type:
Fired,New
Delivery weight: 0.091kgShipping height: 28mmShipping width: 28mmShipping length: 51mm
Item details
Made in USA
Product no.: 749101793 L.E. WILSON 6MM XC FIRED CASE HOLDER Mfr Part: CH-6XC The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for trimming and preparing cases, providing accuracy and uniformity.
It supports the case body during preparation, mimicking the support of a firearm’s chamber.
The FIRED Case Holder is specifically for Neck Sized Cases of the 6mm XC cartridge.
Attributes
Cartridge:
6 mm XC
Case Type:
Fired
Delivery weight: 0.068kgShipping height: 28mmShipping width: 30mmShipping length: 53mm
Item details
Made in USA
Product no.: 749058032 L.E. WILSON 6.5 GRENDEL NEW CASE HOLDER Mfr Part: NCH-65GRN The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for precision work on 6.5 Grendel new brass, including trimming and deburring.
It supports the case body effectively, mimicking a firearm's chamber for consistent and repeatable results.
The NEW Case Holder variant is specifically for new or full length sized cases, as opposed to the FIRED Case Holders for neck sized cases.
Attributes
Cartridge:
6.5 Grendel
Case Type:
New
Delivery weight: 0.045kgShipping height: 30mmShipping width: 26mmShipping length: 52mm
Item details
Made in USA
Product no.: 749058039 L.E. WILSON 300 AAC BLACKOUT CASE HOLDER Mfr Part: CH-3ACC The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for precision tasks such as trimming and deburring, ensuring ultimate accuracy and uniformity.
This case holder supports the case body like a firearm chamber, providing consistent results and repeatability for both fired and new cases.
Compatible with 300 AAC Blackout cartridges, the holder is available for different case types including Fired, New, Neck Sized, and Full-Length Sized cases.
Product no.: 749058034 L.E. WILSON 7.5X55MM SWISS NEW CASE HOLDER Mfr Part: NCH-7555 The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for trimming and preparing new, unfired 7.5 x 55 mm Swiss brass cases.
It ensures ultimate accuracy and uniformity in case preparation, supporting the case body like a firearm's chamber.
This case holder is compatible with new or full length sized cases, manufactured for consistent results and repeatability.
Attributes
Cartridge:
7.5 x 55 mm Swiss
Case Type:
New
Delivery weight: 0.113kgShipping height: 28mmShipping width: 26mmShipping length: 50mm
Item details
Made in USA
Product no.: 749058033 L.E. WILSON 6.8MM REMINGOTN SPC NEW CASE HOLDER Mfr Part: NCH-SPC The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for trimming and preparing new, unfired brass or full-length sized cases.
It provides high accuracy and uniformity in case preparation, supporting the case body like a firearm chamber.
Compatible with 6.8 mm Remington SPC, 22 Nosler, and 224 Valkyrie cartridges, this case holder is made for new case types.
Attributes
Cartridge:
6.8 mm Remington SPC,224 Valkyrie,22 Nosler
Case Type:
New
Delivery weight: 0.045kgShipping height: 30mmShipping width: 30mmShipping length: 52mm
Item details
Made in USA
Product no.: 749058037 L.E. WILSON 22-250 ACKLEY IMPROVED FIRED CASE HOLDER Mfr Part: CH2250A The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749058042 L.E. WILSON 375 RUGER CASE HOLDER Mfr Part: CH-375RUG The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749058044 L.E. WILSON 7.62X39MM CASE HOLDER Mfr Part: CH-76239 The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for case trimming and preparing processes such as primer pocket reaming, neck reaming, and deburring.
It ensures ultimate accuracy and uniformity in trimming, supporting the case body similarly to a firearm's chamber.
The case holders are compatible with 7.62 x 39 mm Russian cartridges and work with both fired and new cases, including those that are neck or full-length sized.
Attributes
Cartridge:
7.62 x 39 mm Russian
Case Type:
Fired,New
Delivery weight: 0.045kgShipping height: 28mmShipping width: 28mmShipping length: 52mm
Item details
Made in USA
Product no.: 749011924 L.E. WILSON 284 SHEHANE NEW CASE HOLDER Mfr Part: CH-284S The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749014773 L.E. WILSON 6MM PPC FAMILY FIRED OVERSIZED CASE HOLDER Mfr Part: CH-PPC0 The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749014774 L.E. WILSON 6MM PPC FAMILY NEW CASE HOLDER Mfr Part: NCH-PPC The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for various case preparation tasks including trimming, primer pocket reaming, neck reaming, and deburring.
It offers high accuracy and uniformity in case trimming due to its unique design that mimics a firearm's chamber to support the case body.
There are specific Case Holders for different case conditions: NEW Case Holders for new or full length sized brass, and FIRED Case Holders for neck sized cases.
Product no.: 749001623 L.E. WILSON 30-40 KRAG FIRED CASE HOLDER Mfr Part: CH-3040 The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749001624 L.E. WILSON 8X57MM MAUSER FIRED CASE HOLDER Mfr Part: CH-8MAUS The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for precision case trimming and preparation, supporting the case like a firearm chamber.
This case holder is specifically manufactured for 8x57mm Mauser fired cases, ensuring consistent results and repeatability.
It is suitable for neck sized cases, with other types available for new, unfired or full length sized brass.
Attributes
Cartridge:
8 mm Mauser (8 x 57 mm Mauser)
Case Type:
Fired
Delivery weight: 0.136kgShipping height: 28mmShipping width: 28mmShipping length: 51mm
Item details
Made in USA
Product no.: 749001626 L.E. WILSON 303 BRITISH CASE HOLDER Mfr Part: CH-303B The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749001662 L.E. WILSON 22-250 REMINGTON CASE HOLDER Mfr Part: CH-2250 The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for trimming and preparing cases, supporting the case body like a firearm chamber.
Case Holders are precision manufactured for consistent results and can be used with both fired and new cases, including neck or full-length sized.
Compatible with multiple cartridges including 22-250 Remington, 250 Savage, and 6 mm International, catering to a range of firearms.
Attributes
Cartridge:
22-250 Remington,250 Savage,6 mm International
Case Type:
Fired,New
Delivery weight: 0.113kgShipping height: 28mmShipping width: 28mmShipping length: 53mm
Item details
Made in USA
Product no.: 749101791 L.E. WILSON 6.5 CREEDMOOR FAMILY FIRED CASE HOLDER Mfr Part: CH-65CRE The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749101792 L.E. WILSON 6.5 CREEDMOOR FAMILY NEW CASE HOLDER Mfr Part: NCH-65CRE The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for trimming and preparing new, unfired 6.5 Creedmoor and 6mm Creedmoor brass cases.
It ensures ultimate accuracy and uniformity in case preparation, supporting the case like a firearm chamber.
The case holders are precision manufactured for consistent results and can accommodate Fired, New, Neck or Full Length sized cases.
Attributes
Cartridge:
6.5 Creedmoor,6mm Creedmoor
Case Type:
New
Delivery weight: 0.091kgShipping height: 28mmShipping width: 28mmShipping length: 53mm
Item details
Made in USA
Product no.: 749101794 L.E. WILSON 6MM XC NEW CASE HOLDER Mfr Part: NCH6XC The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for various case preparation tasks including trimming, reaming, and deburring.
It offers high accuracy and uniformity in case trimming due to its unique design that mimics a firearm's chamber.
This particular model is compatible with 6mm XC new, unfired brass or cases that have been full length sized.
Attributes
Cartridge:
6 mm XC
Case Type:
New
Delivery weight: 0.045kgShipping height: 28mmShipping width: 25mmShipping length: 53mm
Item details
Made in USA
Product no.: 749017476 L.E. WILSON 338 NORMA MAGNUM FIRED CASE HOLDER Mfr Part: CH-338NM The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for various case preparation tasks including trimming, primer pocket reaming, neck reaming, and deburring.
This Case Holder provides high accuracy and uniformity, supporting the case body similarly to a firearm chamber, ensuring consistent results.
It is specifically made for 300 Norma Magnum and 338 Norma Magnum fired cases, although it can accommodate new, neck-sized, or full-length sized cases if not specified.
Attributes
Cartridge:
300 Norma Magnum,338 Norma Magnum
Case Type:
Fired
Delivery weight: 0.095kgShipping height: 25mmShipping width: 30mmShipping length: 48mm
Item details
Made in USA
Product no.: 749017477 L.E. WILSON 338 NORMA MAGNUM NEW CASE HOLDER Mfr Part: NCH-338NM The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
The L.E. Wilson Rifle Case Holder is designed for various case preparation tasks including trimming and deburring.
It provides high accuracy and uniformity, supporting the case body like a firearm chamber.
This New Case Holder is compatible with new or full length sized 300 Norma Magnum and 338 Norma Magnum brass.
Attributes
Cartridge:
300 Norma Magnum,338 Norma Magnum
Case Type:
New
Delivery weight: 0.095kgShipping height: 30mmShipping width: 30mmShipping length: 51mm
Item details
Made in USA
Product no.: 749018856 L.E. WILSON 6.5MM PRC FIRED CASE HOLDER Mfr Part: CH-PRC The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749001611 L.E. WILSON 225 WINCHESTER FIRED CASE HOLDER Mfr Part: CH-225WIN The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Product no.: 749001614 L.E. WILSON 225 WINCHESTER NEW CASE HOLDER Mfr Part: NCH-225W The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Specs:Cartridge: 223 WSSM (Winchester Super Short Mag), 243 WSSM (Winchester Super Short Mag), 25 WSSM (Winchester Super Short Mag), WSSM FamilyCase Type: Fired
Cartridge:
223 WSSM (Winchester Super Short Mag),25 WSSM (Winchester Super Short Mag),243 WSSM (Winchester Super Short Mag),WSSM Family
Case Type:
Fired
Delivery weight: 0.068kgShipping height: 28mmShipping width: 30mmShipping length: 53mm
Item details
Made in USA
Discover the L.E. WILSON .257 Weatherby Magnum Fired Case Holder for precise trimming. Perfect for your reloading needs! ✨
The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
More...
Customer ratings for L.E. WILSON 257 WEATHERBY MAGNUM FIRED CASE HOLDER
Number of ratings: 20
From brownells.com: 20
Average rating: 3.8
Does Not Work With Hornady Dies(08/07/2017)
Recently bought this case holder to use after full-length resizing with Hornady New Dimension Custom Grade K-31-specific 7.5x55 Swiss dies. Case mouths would not exit the holder, making trimming impossible. However, I measured the shoulder on the resized brass and a fresh GP-11 cartridge. The GP 11 measured .448." The "resized" brass measured .472." I think the blame clearly lies with Hornady's dies, not the Wilson trimmer. Nevertheless, I am leaving this review because I want other shoppers to be aware that if they plan to use the Hornady dies, they will need to buy the trimmer holder for FIRED cases, Wilson item CH7555.
Frustrated(28/01/2018)
Bought the original one about a year ago, waiting for a rifle to get finished finally got my rifle she's a dream by the way. Now comes the not so good, I load 308, 223, 6.8, and various pistol calipers after my first shooting with new rifle cleaned and resized brass case goes all the way through, does not stop on shoulder as others, so I'm thinking I got a bad one it happens returned to brownells for a new one, same thing happening all over again, this time, it's not rocket scientist stick the case in the gage until it stops on shoulder set your cutter to desired length and trim not that hard. So I'm surprised that I got so lucky to get two too many out of spec maybe case gages
Maybe I do need to be a rocket scientist(08/02/2018)
So it's Charles again from previous post. Would like to remove the poor rating I gave product earlier. I have been using the wrong holder I needed new and full length resized holder for my brass, just goes to show that us part time rocket scientist aren't so smart after all. Product is great.
Works great!(20/04/2011)
Perfect trim jobs from my Wilson trimmer. Just be sure to tap the case into the holder good so it doesn't spin when you go to trim.
nothing special(27/03/2011)
soft material,dents easily when dropped to the concrete floor.
Drop Proof(31/12/2011)
Works great when you don't drop it on a concrete floor.
Works for both New & Fired Lapua Brass(01/03/2011)
If you're using Laupa 6mm BR Norma brass, you won't need to buy the Wilson Trimmer Holder for New Brass. It fits perfect in this one! Just the neck of new Lapua brass protrudes from the Wilson Trimmer Holder for New Brass. I bought both and only use this one.
GREAT Trimmer(01/05/2017)
FINALLY, a case holder that is accurate, easy to use. and very well made. This case holder, combined with the Stainless Ultimate Trimmer, is a perfect match. For those calibers for which Wilson makes a case holder, this combo will be my trimmer of choice.
Buy CH-308W, not this one(30/08/2012)
This holder will NOT work with fully re-sized brass.
Works with my full length and resized(01/11/2012)
Works as advertised. If it does not call L.E. they will get you straighted out. It is probably due to a tight chamber or oversized. Case Holders are set up to work with 98% of the chambers that are out there, but if it does not they will get you the correct holder for you.
Limited use with fully sized 308 cases(20/03/2018)
Let me say, first, that Wilson products and services are top notch, as is Brownells service. (Wilson trimmers are the most accurate I've ever used. I've trimmed hundreds of rifle cases in various calibers.) This particular case holder works for 243 fully sized (new) and fired brass. It does not work with once fired Lake City or Federal fully sized 308 brass. I used two different Redding presses and standard FL sizing Redding and RCBS dies to check this holder. The sized cases would not extend far enough to be trimmed. I do not have small base dies which reduce the case size to a greater degree to allow more efficient chambering in semi-automatic rifles. I did not use factory new, unfired brass. Based on what I've experienced, I would recommend BOTH case holders to prospective buyers. Rifle chambers vary from Target to Hunting to Military. This is not the fault of the manufacturer or the vendor.
I use these trimmer holders in my Sinclair Micrometer Case Trimmer and get superb results. I trim my cases .010 to .015" under SAAMI maximum case length and get amazingly uniform results. The variation is + or - .0005". The jamb fit of the case holds the case in precise alignment. The only downside is the holder grabs the case so snug I have to to tap each trimmed case on a pad to remove it from the holder. Not a big minus when the results I get are so consistent.
Can be upgraded for Lapua Brass(18/02/2011)
You may be able to alter this Holder slightly to avoid having to also buy a New 204 Brass Holder. New Lapua Brass sits too deep inside this Holder, so that the Case Length Trimmer's threaded Adjustment Stop can't reach the case head. But by using a drill press, you can widen the back end of this Holder's hole so that the Adjustment Stop could enter the hole and reach the New Brass case heads. I didn't need to drill very deep, just about 0.1". I used a bit that was a little wider than the Adjustment Stop's face. I don't know if this will work for Norma brass, as I only use Lapua brass.
Not necessary for new Lapua 6mm BR Brass(18/02/2011)
While waiting for my new 6mm BR to arrive I started tooling up and bought both of the Wilson Trimmer Holders for new and fired brass. I'm using only Lapua Brass and I quickly found out that the new brass fits better in the standard Wilson Trimmer Holder.
Need To Revise My Original Rating(31/07/2011)
Unlike new Lapua brass, new Norma brass fits very well in this case holder because of its smaller diameter.
You may not need one of these.(18/02/2011)
You may not need to buy this New Brass Holder, if you buy the standard Holder (for fired brass) and alter it slightly. New Lapua Brass sits too deep inside the standard Holder, so that the Case Length Trimmer's threaded Adjustment Stop can't reach the case head. Using my drill press, I widened the back end of the Holder's hole so that the Adjustment Stop could enter the hole and reach the new brass case heads. I didn't need to drill very deep, just about 0.1". I used a bit that was a little wider than the Adjustment Stop's head. I don't know if this will work for Norma brass, as I only use Lapua brass.
You will need this holder for new brass(01/11/2012)
If you do not want to modify your holder and void your warrenty, you will need this holder.
L.E. will back up everything they make, they added this because your cases sit too deep in the fired holder which does not allow you to trim the case accurately. Bottom Line you need for new brass or full lenght sized brass.
Quality(30/04/2018)
Typical Wilson quality product. Works great to produce exact length cases.
Won't Work for 30-30 with Neck Bumped up(29/03/2014)
If you bump the neck up on your 30-30 cartridges to prevent excessive stretching of the brass there isn't enough of the brass extending outside of the holder to trim
Details: Using a Hornady Headspace gauge, I have found my fired brass to "Headspace" at 1.503"
I set my Redding die up to keep my shoulder at 1.501" to prevent excessive stretching of the brass when resizing
I have been trimming my brass to 2.030", but when I changed where my shoulder was, it seems I can no longer use the Wilson Trimmer Case Holder because the end of my brass is still inside the case holder.
Historically, using the generic Redding die settings my shoulder was at 1.485". This seemed to give me enough brass outside of the case holder to trim.
Wilson fixed my problem(28/04/2014)
I wrote a review on 3/29/14 with complaints about the holder not allowing you to trim if you bump up the neck of the case. I have since been able to contact Wilson and they were nice enough to machine the holder at no cost (outside of shipping it to them). The holder will now work with both cases (standard factory and with the neck bumped up to fit my rifle). I am very happy with the customer service I received and the holder now works great.