English-made with heat-treated, flat-nosed jaws. Smooth-jawed model gives a tight, non-marking grip. Serrated model holds tightly and includes a lengthwise groove to hold wire or drilled rod.
SPECS: Both; 5" (12.7cm) long, 1-1/8" (2.9cm) deep throat, open to 7/16" (11.1mm) wide. Nickel plated handles, blued jaws.
More...
Customer ratings for GROBET FILE CO. OF AMERICA INC FLAT NOSE SMOOTH JAW PARALLEL PLIERS
Number of ratings: 5
From brownells.com: 5
Average rating: 5
Would buy this product again and again(14/10/2009)
Excellent quality..The best I've seen in a long time..The jaws are perfectly parralel the full length and come together so perfectly they will hold a single piece of paper!Perfect size for working with guns of any kind. A little pricey but worth it for the quality!
Smooth Jaw Pliers(20/01/2016)
I have several sets of Barnard Pliers that I have been lucky enough to source from the U.S.A.
Most of these pliers have serrated jaws, which are fine for most work and with the addition of a smooth jaw set I have all of the bases covered. There is no substitute for quality tools.
I use my serrated parallels for precise placement of dowel pins when I get ready to press them into place, and also to extract pins too. I have carefully shaped small diameter spring wire using them as well. I keep them very close nearby my vise because I reach for them all the time. The jaws are tough and the handles fit well into the palm of my hand.
Serrated parallel jaw pliers(01/09/2011)
The description needs to have a drawing or picture of serrations and groove dimensions
NICE tool!(25/01/2013)
Recently, I used the serrated jaw pliers to install a Badger Ordinance Tactical Latch lever (093-249-020WB). The pin/wire relief in the one jaw made the job a cinch.
(If you're interested, I reviewed my installation and use of the pliers on that page.)
While a bit pricey, having the right tool for the job--and a well-made tool--is priceless. They are heavy for being so small, but just the right size for firearms work.
Product no.: 348181105 GROBET FILE CO. OF AMERICA INC FLAT NOSE SMOOTH JAW PARALLEL PLIERS Mfr Part: 46.512501869500054 English-made with heat-treated, flat-nosed jaws. Smooth-jawed model gives a tight, non-marking grip. Serrated model holds tightly and includes a lengthwise groove to hold wire or drilled rod.
Product no.: 348181103 GROBET FILE CO. OF AMERICA INC SERRATED PARALLEL PLIERS Mfr Part: 1811030501869500071 English-made with heat-treated, flat-nosed jaws. Smooth-jawed model gives a tight, non-marking grip. Serrated model holds tightly and includes a lengthwise groove to hold wire or drilled rod.
English-made with heat-treated, flat-nosed jaws. Smooth-jawed model gives a tight, non-marking grip. Serrated model holds tightly and includes a lengthwise groove to hold wire or drilled rod.
SPECS: Both; 5" (12.7cm) long, 1-1/8" (2.9cm) deep throat, open to 7/16" (11.1mm) wide. Nickel plated handles, blued jaws.
More...
Customer ratings for GROBET FILE CO. OF AMERICA INC FLAT NOSE SMOOTH JAW PARALLEL PLIERS
Number of ratings: 5
From brownells.com: 5
Average rating: 5
Would buy this product again and again(14/10/2009)
Excellent quality..The best I've seen in a long time..The jaws are perfectly parralel the full length and come together so perfectly they will hold a single piece of paper!Perfect size for working with guns of any kind. A little pricey but worth it for the quality!
Smooth Jaw Pliers(20/01/2016)
I have several sets of Barnard Pliers that I have been lucky enough to source from the U.S.A.
Most of these pliers have serrated jaws, which are fine for most work and with the addition of a smooth jaw set I have all of the bases covered. There is no substitute for quality tools.
I use my serrated parallels for precise placement of dowel pins when I get ready to press them into place, and also to extract pins too. I have carefully shaped small diameter spring wire using them as well. I keep them very close nearby my vise because I reach for them all the time. The jaws are tough and the handles fit well into the palm of my hand.
Serrated parallel jaw pliers(01/09/2011)
The description needs to have a drawing or picture of serrations and groove dimensions
NICE tool!(25/01/2013)
Recently, I used the serrated jaw pliers to install a Badger Ordinance Tactical Latch lever (093-249-020WB). The pin/wire relief in the one jaw made the job a cinch.
(If you're interested, I reviewed my installation and use of the pliers on that page.)
While a bit pricey, having the right tool for the job--and a well-made tool--is priceless. They are heavy for being so small, but just the right size for firearms work.