Designed for M-LOK compatible handguards, the MAGPUL rail allows attachment of 1913 Picatinny spec accessories.
Made from a reinforced polymer, offering strength and lightweight with beveled ends to prevent snagging.
Comes in various lengths with the 5-slot version being 2.375 inches and includes all necessary hardware for easy installation.
The MDT M-LOK Baker Wings are designed to enhance stability and control for shooting from unstable positions and when using a front bag.
They are compatible with any M-LOK chassis or stock and specifically fit MDT ACC, ESS, TAC21, and LSS-XL Gen2 chassis, as well as precision AR-10/15 forends.
Each wing is 229 mm long, adds approximately 2 inches in width to the forend, and is made from 6061-T6 aluminum, weighing 0.84 lbs.
The MDT M-Lok Arca Swiss Rail is designed for attaching MDT Chassis rifles to ARCA interfaces on tripods and support gear.
This rail is available in both a standard flat profile for general M-LOK surfaces and an angled profile to match the MDT LSS-XL Gen2 underside.
Constructed from aluminum with a Mil-spec Type III hard-black anodization, the rail is durable and available in multiple lengths.
Constructed from 6061 aluminum with a hard coat anodized finish, ensuring durability and a lifetime of service.
Designed as a one-piece Picatinny scope rail, it is 5.0 inches long and includes mounting screws for easy installation.
100% Made in the U.S.A., this top rail fits Marlin 1894 models and is compatible with Henry 38/357, 44 Mag, and 45 Colt receivers, carrying a lifetime warranty.
Easy to install top rail for HK MP5 that allows mounting of optics and accessories, with all necessary tools included.
Constructed of 6061 aluminum with a hard coat anodized finish, ensuring durability and a lifetime of service.
Designed and manufactured in the USA, the rail is 922R Compliant and comes with a lifetime warranty from Midwest Industries.
The MDT Arca Swiss Rail is made from Mil-spec Type III hard-black anodized aluminum.
It is designed with a flat profile for infinite adjustment and is compatible with Magpul MOE hole spacing.
It fits various MDT chassis and stocks, including LSS, HS3, TAC21, LSS-22, and the discontinued LSS-XL.
The Area 419 Fixed Barricade is a non-moveable stop designed for 12” Arcalock and MPA rails, providing a stable rear barricade.
It includes a 3/32 wrench for installation, features a grooved surface for grip, and is machined from 6061-T6 Aluminum with a Type III Black Hardcoat Anodized finish.
The barricade uses a pinch clamp and set screw for secure attachment, preventing slippage by engaging with the ARCALOCK cuts.
The Brigand Arms M-LOK Aluminum Backing Plate is designed to attach accessories to AR-15s without adding significant weight.
It is compatible with the lightweight Brigand Arms carbon-fiber handguard and negates the need for heavy Picatinny rails.
The backing plate is lightweight at only 0.26 ounce and comes with the necessary screws and a hex wrench for installation.
Compatible with all M-LOK systems, the rail sections allow for the attachment of 1913 Picatinny accessories.
Available in both aluminum and polymer, with aluminum being Mil-Spec anodized for durability.
Designed with beveled ends to prevent snagging and sharp edges, and comes with necessary hardware for installation.
The Area 419 Arcalock 14" Universal Dovetail Rail features a proprietary clamp design with 65 locking positions for a secure mechanical lock, preventing any movement.
It is compatible with standard Arca accessories and follows the RRS 1.5" Dovetail Standard, ensuring lever clamps fit properly.
Constructed from durable 6061-T6 Aluminum with a Type 3 Hard Coat anodized finish, the rail can be attached at up to 4 points on various rifle and stock configurations for enhanced stability.
The Arisaka Indexer is designed for M-LOK systems, offering a low profile, minimal control accessory to improve rifle handling.
It serves multiple functions such as a hand stop, barricade stop, and helps in pulling the rifle into the shoulder for better control.
Made from 6061-T6 aluminum with a hard coat anodized finish, the Indexer is durable, lightweight, and requires a T25 Torx wrench for installation.
MDT's Scope Base Picatinny Rails are machined from 6061-T6 aluminum and hard-anodized for durability.
These rails are designed with a 40 MOA incline to provide additional elevation adjustment for scopes.
They feature a profiled underside for flush mounting and a recoil lug where applicable to the action’s design.
The Kinect™ by KDG is a QD mounting system for MLOK™ that allows for easy and proper accessory attachment without over-tightening.
It features a simple operation with two spring-loaded wedges that lock into place without the need for tools when pressed into the MLOK™ slot.
This M-LOK rail section is made of black anodized aluminum, measuring 1.68" in length and is compatible with any MLOK rail system.
The AR-15 Picatinny Direct Thread UFIR Rail is an aluminum accessory rail that allows for the mounting of various accessories such as lights, grips, and bipods.
It is designed with 11 cross slots following MIL-STD-1913 specifications for a wide range of accessory compatibility.
The rail is made of 6061 T6 aluminum with a mil-spec Type III hardcoat anodized finish in matte black, measuring 4.5 inches in length.
The Area 419 RailChanger features an ARCALOCK clamp compatible with ARCALOCK and standard Arca/RRS dovetail rails.
Designed for use with RailChanger equipped support bags for hands-free operation on various shooting supports.
Constructed from 6061-T6 Aluminum with a Type 3 hard coat anodized finish for durability.
The adapter allows for quick, on-the-fly adjustments for bipods and tripods due to the Arca-Swiss Quick Release System, offering a competitive edge in precision rifle sports.
Compatible with JP MK III Hand Guards and potentially other brands, it mounts easily and provides a stable, non-rotating platform for supported shooting.
Constructed from sturdy 6061-T6 aircraft-grade aluminum with a resilient Type III hard coat anodized finish, ensuring durability and longevity.
The Area 419 Arcalock 12” MLOK Attachment features a mechanically locking 12" dovetail rail compatible with RRS 1.5" standard and offers a full-length attachment area on the stock forend.
Made from durable 6061-T6 Aluminum, the rail is Type 3 Hard Coat anodized for extra durability and comes with all necessary M-LOK mounting hardware.
Designed and manufactured in the USA, the rail's serrated sides interface with Area 419's proprietary clamp design ensuring a secure, movement-free attachment to precision rifles.
The Daniel Defense 2.5" M-LOK Picatinny Rail section allows for the attachment of Picatinny accessories to M-LOK Handguards.
Constructed from 6061-T6 Aluminum with a Type III Hard Coat Black Anodizing, it is extremely lightweight, weighing less than an ounce.
Manufactured in the USA, this rail section ensures secure mounting of accessories to AR-15 M-LOK handguards.